car wont go into gear after clutch install

Otherwise the disc and flywheel remain mated and you wont be able. He may or may not have a defective unit.

How Dual Clutch Transmissions Work Dual Clutch Transmission Clutch Plate Manual Transmission

Southbend Stage 4 FE Flywheel.

. Posted by 7 minutes ago. Could there possibly be a bolt thats too tight thats. Fidanza Lightweight with brand new plate As the title says for some reason after putting in a new clutch and replacing the output shaft seal and the input shaft bearingseal it simply wont shift into gear if the car is turned on.

As the friction disc down you have to press the pedal further and further down to move it away from the flywheel. Took the old modular clutch apart Drilled out the rivets. My slave bleeder was rusted to i replaced it with a new one from dealer.

And on that one time when you press it and the car still creeps forward you know you have a problem. Tapped the holes M10 x 125. When u installed the new clutch disc and plate did you align it.

In normal modern stop-and-go driving you probably press the clutch pedal in every few seconds. Try this on the clutch pedal. Pulling everything apart was pretty easy.

Voting is now live for Aprils E46 of the Month Challenge. Discussion Starter 1 Aug 13 2017. Well the clutch isnt releasing fully which is why it wont go into gear with the engine running.

This is on an 01 Mustang with the baby 38l and a T5OD tranny. I took everything back apart and checked the clutch plate and it is in there correctly. When the car was raised front end up still and put together enough.

2 of 2 Go to page. The transmission will shift in and out of gear without any issue when the car is not running. I bled the system but for some reason the pedal still feels the same so i thought it was bled properlyI started the car but it wont get into gear but it will go into gear whens its off.

I installed a new clutch and now when the car is on it wont shift into any gear. Joined Nov 29 2008. I have had the system bled numerous times by different places.

If the vehicle was shafting fine prior to installation or was able to be driven whether the clutch was slipping or not and now the vehicle will not move at all the issue is with the workmanship or the clutch set itself. If you have a manual transmission try to press the clutch pedal all the way down to the floor before trying to change gears. The car starts moving if you push it to 1st.

Adjusted the pedal even put a new slave cylinder on in case it was that. 6 Nov 11 2010. The transmission wont shift and the car makes a grinding sound when the engine is running.

Jump to Latest Follow Hey everyone. But I can start the car in gear and let go of the clutch and it moves forward just fine. Drives perfectly on every other gear just wont fully engage.

Sometimes its impossible to go into 1st or reverse. The car will shift fine once you are moving it will go into 1st-5th gears just fine if the car comes to a dead. Either way modular clutch or not the transmission has to be removed.

Put it all back together and the shifter goes through all the gears no trouble but when turned on will not go into any gear. The clutch isnt disengaging it seems. Scuffed up the pressure plate and flywheel sides the installed a brand new clutch disc.

Discussion Starter 1 Mar 9 2016. A few months back I installed a Mcleod clutch flywheel and ss line along with new Ford slave and RP trans fluid. Drives perfectly on every other gear just wont fully engage with first.

The signs that the car will show at this time are. Joined May 16 2012. 12 Feb 12 2022.

Press the Clutch Pedal Down More. This winter i upgraded my clutch to stage 4 so later on i can boost my KA24de. There is either still air in the clutch system you have a bad master or slave cylinder the clutch isnt right or the TOB isnt right.

I did not measure it at all but tried to go by the casting marks which look like where the area should have been. Theres is a screw I cant recall which direction but your pedal should be a bit higher turn screw 2 or 3 times then test it out-- since its an aftermarket clutch it wont engage how it did before so you have to adjust clutch pedal same thing happen to me hopefully it works for you. Bolted it all together using 25mm long grade 10.

Cant get into 1st gear after changing clutch. Sometimes a part fails and the clutch goes from working normally to not working in an instant. It wont come out of the reverse gear.

Clutch fails to disengage when pressed. Car wont go into gear while the engine is running after new clutch install. 21 - 26 of 26 Posts.

Besides pulling out of first gear will feel harder than normal. I installed a ACT xtreme duty clutch on my 02 wrx and ever since Ive had it installed it wont go into gear while the engine is running and the car is not moving. This 1 I must have bled my clutch 15 times.

Bad Habits That Will Destroy Your Car Clutch